Basic Info.
Shell Material
Flame Retardant PC Plastic
Certification
CE, ROHS, UL,Zhaga,CB,Ukca
Product Description
ParametersPower Supply | Rated voltage:12~24VDC,3W It is recommended that the transient current response capacity reach 1A |
Average power consumption | 1.2W |
Dimming Interface | Type:0~10V Accuracy:±2% Drive Current:20mA(Typical) |
Communication | LTE+Sub-G |
Spectral Acquisition Range | Range: 0.01~64000Lux Accuracy: ± 2% Wavelength:350~1100nm,Peak wavelength: 550nm |
Turn on Illuminance | 100Lux(±10) |
Turn off Illuminance | Reflected light + 40Lux(±10)after each turn on Lower limit:50+40Lux(±10); Upper limit:6000Lux(±100) |
Reflected light compensation upper limit | 6000Lux(±100) |
Microwave parameters | Frequency: 5.8 GHz Supported hanging height: < 15m Sensing radius: 4-6 meters Sensing angle:<92 ° |
Linkage distance | ≤1km |
Default Tiny Brightness | 20% |
Default Tiny Light Maintenance Duration | permanent |
Default trigger brightness | 100% |
Default trigger brightness maintenance duration | 30S |
Default Maximum Power Ratio | 80% |
Sensing radius | 4-8m (by 15m hanging height) |
Initialization Action | After startup, the light is turned on at 100% brightness by default, and it is taken over by the device operation mode after 5S |
Lamp on delay | 10S |
Lamp off delay | 10S |
Duration of microwave induction light on | Default 30S platform adjustable |
Microwave error prevention trigger | Possess certain ability to prevent wind, rain, leaves, and small animals |
Trace brightness | Default 20% platform adjustable |
Slightly bright duration | Default permanent platform adjustable |
Network Protocol | MQTT |
SIM card | Cato plug-in type Supports 1.8V USIM cards NANO package |
Remote upgrade | Sustain OTA |
Green LED Indicator Light | Chang Liang: Successfully connected base stations |
Blue LED Indicator Light | Blinking: Connecting to the server Always on: Successfully connected to the server |
Default periodic reporting frequency | 10 minute |
Energy saving strategy | custom |
Electrostatic discharge immunity | Contact discharge: ± 8kV, CLASSB Air discharge: ± 15kV, CLASS B |
Operating Temperature | -40ºC~70ºC |
Storage Temperature | -40ºC~85ºC |
Operating Humidity | 5%RH~96%RH |
IP Level | IP66 |
Structural material | foundation bed:PBT Shell:PC |
Standard | IEC61000-4-2,GB/T2423.10-2008,UL94-V0 |
Certifications | |
Note:All brightness is based on the maximum power ratio and the current light attenuation compensation ratio.Examples of explanation of reflected light compensation mechanism:a). If the light-emitting surface of the lamp is completely shielded and isolated from the light-sensitive surface of the light controller when installed, that is, no reflected light enters the light controller after the lamp is illuminated, then the light-off illuminance at this time is equal to the lower limit, that is, down The illuminance of the second turn off is approximately = the default turn on illuminance + 40 lux compensation value = 50 + 40 = 90 lux;b). If the installation fails to completely shield and isolate the light-emitting surface of the lamp and the light-sensitive surface of the light controller, that is, the reflected light enters the light controller after the lamp is illuminated. If thelamp is lit to 100%, the current environment collected by the light controller If the illuminance is 500lux, the illuminance of the next turn off is approximately = the current ambient illuminance+40=540lux;c). If the power of the lamp is high and the light-emitting surface is very close to the light-sensitive surface of the light controller, the reflected light exceeds the upper limit of compensation after the lamp is turned on to 100%, that is, the light controller detects that the ambient illuminance has been stable after turning on the light If it is greater than 6000lux, the light controller will automatically turn off the light after 60S.Product Summary
The JL-712G3L single lamp intelligent controller adopts the wireless communication mode of LTE CAT1, which has the ability of light sensing and microwave sensing, and supports local wireless linkage function. It can still be linked when the network is disconnected. The dimming output mode is 0-10V. You can use our UM9900 management system for remote monitoring and configuration. This product is only suitable for detecting pedestrians and low-speed vehicles<20km/h.Product size chart
Features
• ZHAGA standard interface*• LTE Cat.1 communication• Synergia Modes Remote Configuration• Motion sensing upto 15m height• Synergying coverage upto 1km• Anti-mulfunction for outdoor purpose• Self-cycling prevented• LED Decay compensation built-in• Multi-sensing Strategy• Fault Dianosis & Report• MQTT Server Online Miguration SupportNote: *Using Port #4 positive with #2 negative for 0~10V dimming control.PIN
PIN | Definition | Type |
1 | 12~24VDC | Power Input |
2 | GND/DIM- | Power Input |
3 | DIM+(0~10V) | Dimming signal output |
4 | NC | _ |
Installation
The interface of the product itself has been fool-proof design, the installation only need to tighten the controller directly to the rotatable base, Insert and tighten clockwise as shown in the figure below, and remove it counterclockwise.The SIM card slot is located in the circular area at the bottom of the product. Refer to the image below.Attentions
If the negative pole of the auxiliary power supply of the driver is separated from the negative pole of the dimming interface, they need to be shorted and connected to the light controller # 2.If the light controller is installed very close to the light source surface of the lamp and the lamp power is relatively large, it may exceed the limit of the reflected light compensation and appear to turn off itself.Because the ZHAGA light controller does not have the ability to cut off the AC power supply of the driver, the customer needs to select a driver with an output current close to 0mA when using the ZHAGA light controller, otherwise the phenomenon that the lamp cannot be completely turned off may occur. As shown in the output current curve of the driver specification, the lowest output current is close to 0mA.FAQQ1: Are you a Factory?
Yes. We are the manufacture factory, and our factory has specialized in industrial electronic products for nearly 25 years.
Q2: Do you have stock products to sell?
No, We produce these electronic products according to the customer's requirement, It also means material, density, shape, size, design, the quantity will depend on what you.
Q3: Does the electronic product can be printed as a LOGO?
Yes, we can print the logo as per your specific requests.
Q4: What advantages do you have?
We are the Factory, and we have the ability to carry out a production schedule for punctual delivery. More importantly, We can provide free samples for quality evaluation.
Q5: If I want to get a Quotation, what information needs to be provided to you?
In general, Type and Quantity.
Address:
2099 Yedao Road, Haiyan, Jiaxing, Zhejiang, China
Business Type:
Manufacturer/Factory
Business Range:
Computer Products, Consumer Electronics, Electrical & Electronics, Lights & Lighting
Management System Certification:
ISO 9001
Company Introduction:
Zhejiang Long-Join Electronics Co., Ltd. is a wholly-owned subsidiary of Shanghai Long-Join Intelligent Technology Inc. (Stock Code: 837588). The company was founded in 1996, for more than 20 years, Long-Join has been committed to providing multi-dimensional comprehensive industrial services such as design, research and development, production and manufacturing, software management platform, market application, etc. For the lighting industry and energy conservation field. The photo controller series is a world-class leading product in the industry. Our products serve all over the world and are partners of well-known brands and industry giants at home and abroad, such as Signify, GE Lighting, IDEAL INDUSTRIES, Eaton Cooper, HPWINNER, OPPLE, Leedarson, and SNC-LIGHTING. Shanghai Long-Join Intelligent Technology Headquarters and Zhejiang Long-Join Electronics are both National High-tech Enterprises, and Shanghai Long-Join Intelligent Technology is also a National Specialized "small giant" Enterprise. The company adheres to the business purpose of "Innovation and Excellence", improves and iterates the product series, and more accurately serves the industry and related fields.
Zhejiang Long-Join Electronics Manufacturing Base is located in Haiyan County, Zhejiang Province, close to Shanghai and Ningbo Hangzhou Bay. The production base covers an area of 35 mu, with an area of about 38000 square meters. It has passed the ISO9001 quality management system certification. The factory has about 200 members, including 3 senior engineers and 12 engineers, about 8.5 million sets of light-controlled switch components are exported annually (including self-export, agent export and supporting re-export of lamp enterprises). There is a municipal laboratory for intelligent street lamp control in the plant, which currently has 70 independent patents and plans to realize fully automatic production in 2024.
" Long-Join′s members make the sky more blue " is the common vision of all employees of Zhejiang Long-Join. We will continue to uphold the ingenuity of China′s intelligent manufacturing and rely on carbon neutrality Under the new era background, we will give full play to the advantages of design, research and development, production and manufacturing, software platform and other links, and develop together with partners in the industry and field.